For first time visitors I recommend this archive for some of my best posts.
2725. 15" long, take a look at Neatorama for more guesses and a chance to win a T-shirt:
![]()
Larger image
![]()
Larger image
![]()
2726. 10" to 37" long:
![]()
These next three were all sent in by people who are looking to identify their items.
2727. 9" long:
![]()
![]()
![]()
![]()
2728. 11" long, text on it reads "Made in USA ; Bristol, Newark NJ; Pats. pending":
![]()
Larger image
2729. This belonged to someone's great grandfather:
![]()
2730. 60" tall:
![]()
![]()
![]()
Answers:
2725. A Depth Gauge "for sounding in depths of from one hundred fathoms", it was manufactured by John E. Hand & Sons. The directions read: "Place gauge in sinker, cap end up. Allow the whole to run out until it bottoms, wind in, remove gauge from sinker. Hold gauge vertically, unscrew cap and measure water in gauge with one of the scales (first chalk surface of scale,) the highest wet point on scale will indicate sounding in fathoms." Patent number 1,282,075
![]()
Larger image
![]()
Larger image
![]()
Larger image
![]()
2726. A rivet spacer![]()
that was made for spacing rivets on aircraft, though it could be used for spacing anything else:
![]()
2727. An EX-2000 pliers tool for servicing termite control stations:
![]()
![]()
![]()
![]()
2728. This is probably a carving fork/meat holder for use with a roast or ham:
![]()
Larger image
2729. This is most likely a bodhran tipper, which is a type of drum stick for playing a bodhran drum, or it could possibly be a beater for an African drum:
![]()
2730. An M1921 combination small arms rack, circa 1925, twenty M1903 or M1917 rifles fit into the lower section while twenty M1923 revolvers fit into the upper section. It was designed and manufactured at the Rock Island Arsenal Pattern Shop.
![]()
![]()
![]()
Are you interested in Old Tools and Tool Collecting? Want to learn more about tools, and meet some great people who have the same interests? Please take a minute to check out the Mid-West Tool Collectors Web Site at this link: www.mwtca.org.
![]()
To submit photos, send them to the address in my profile, please include dimensions, any text on the item, and where it was found.
Last week's set is seen below, click here to view the entire post.
![]()
More discussion and comments on these photos can be found at the newsgroup rec.puzzles.
2725. 15" long, take a look at Neatorama for more guesses and a chance to win a T-shirt:
Larger image
Larger image
2726. 10" to 37" long:
These next three were all sent in by people who are looking to identify their items.
2727. 9" long:
2728. 11" long, text on it reads "Made in USA ; Bristol, Newark NJ; Pats. pending":
Larger image
2729. This belonged to someone's great grandfather:
2730. 60" tall:
Answers:
2725. A Depth Gauge "for sounding in depths of from one hundred fathoms", it was manufactured by John E. Hand & Sons. The directions read: "Place gauge in sinker, cap end up. Allow the whole to run out until it bottoms, wind in, remove gauge from sinker. Hold gauge vertically, unscrew cap and measure water in gauge with one of the scales (first chalk surface of scale,) the highest wet point on scale will indicate sounding in fathoms." Patent number 1,282,075
Larger image
Larger image
Larger image
2726. A rivet spacer
that was made for spacing rivets on aircraft, though it could be used for spacing anything else:2727. An EX-2000 pliers tool for servicing termite control stations:
2728. This is probably a carving fork/meat holder for use with a roast or ham:
Larger image
2729. This is most likely a bodhran tipper, which is a type of drum stick for playing a bodhran drum, or it could possibly be a beater for an African drum:
2730. An M1921 combination small arms rack, circa 1925, twenty M1903 or M1917 rifles fit into the lower section while twenty M1923 revolvers fit into the upper section. It was designed and manufactured at the Rock Island Arsenal Pattern Shop.
Are you interested in Old Tools and Tool Collecting? Want to learn more about tools, and meet some great people who have the same interests? Please take a minute to check out the Mid-West Tool Collectors Web Site at this link: www.mwtca.org.
To submit photos, send them to the address in my profile, please include dimensions, any text on the item, and where it was found.
Last week's set is seen below, click here to view the entire post.
More discussion and comments on these photos can be found at the newsgroup rec.puzzles.